Battery – North America Chevrolet Silverado 1500

The original equipment battery is maintenance free. Do not remove the cap and do not add fluid.

Refer to the replacement number shown on the original battery label when a new battery is needed. See Engine Compartment Overview 0 328 for battery location.

Stop/Start System.

Vehicles equipped with a 2.7L L3B, 3.0L LM2, 5.3L L84 or 6.2L L87 are equipped with a Stop/Start system to shut off the engine to help conserve fuel. See [linkin] Stop/Start System 0 210.

Vehicles with the Stop/Start system have an Absorbed Glass Mat (AGM) 12-volt battery. Installation of a standard 12-volt battery will result in reduced 12-volt battery life. When using a 12-volt battery charger on the 12-volt AGM battery, some chargers have an AGM battery setting on the charger. If available, use the AGM setting on the charger to limit charge voltage to 14.8 volts.

Follow the charger manufacturer’s instructions..

[symbolwarning] Warning.

WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Batteries also contain other chemicals known to the State of California to cause cancer. WASH HANDS AFTER HANDLING. For more information go to www.P65[symbolwarning] Warning.s.ca.gov/ passenger-vehicle.

See [linkin] California Proposition 65 [symbolwarning] Warning. 0 325 and the back cover.

Vehicle Storage..

[symbolwarning] Warning.

Batteries have acid that can burn you and gas that can explode.

You can be badly hurt if you are not careful. See [linkin] Jump Starting North America 0 415 for tips on working around a battery without getting hurt.

Infrequent Usage: Remove the black, negative (−) cable from the battery to keep the battery from running down.

Extended Storage: Remove the black, negative (−) cable from the battery or use a battery trickle charger.

Negative Battery Cable Disconnection..

[symbolwarning] Warning.

Before disconnecting the negative battery cable, turn off all features, turn the ignition off, and remove the key, if equipped, from the vehicle. If this is not done, you or others could be injured, and the vehicle could be damaged..

Caution.

If the battery is disconnected with the ignition on or the vehicle in Retained Accessory Power (RAP), the OnStar back-up battery will be permanently discharged and will need to be replaced.

1. Make sure the lamps, features, and accessories are turned off.

2. Turn the ignition off and remove the key, if equipped.

For vehicles equipped with the Stop/ Start system:

1. Loosen and remove the negative battery cable nut (1) at the battery sensor connection.

2. Remove the negative battery cable (2) from the battery sensor stud.

3. Cover the negative battery cable terminal, battery sensor stud, and negative battery post with a non-conductive material to prevent any contact with the negative battery cable.

For vehicles not equipped with the Stop/Start system:

1. Loosen the negative battery cable nut (1).

2. Remove the negative battery cable clamp (2) from the negative battery post.

3. Cover the negative battery cable clamp, and negative battery post with a non-conductive material to prevent any contact with the negative battery cable.

Negative Battery Cable Reconnection..

Caution.

When reconnecting the battery:

• Use the original nut from the vehicle to secure the negative battery cable. Do not use a different nut.

If you need a replacement nut, see [linkin] your dealer.

• Tighten the nut with a hand tool. Do not use an impact wrench or power tools to tighten the nut.

The vehicle could be damaged if these guidelines are not followed..

Caution.

Do not use paints, lubricants, or corrosion inhibitors on the nut that secures the negative battery cable to the vehicle. This could damage the vehicle.

For vehicles equipped with the Stop/ Start system:

1. Install the negative battery cable to the battery sensor stud.

2. Install the negative battery cable nut to the battery sensor stud and tighten.

3. Turn the ignition on.

For vehicles not equipped with the Stop/Start system:

1. Install the negative battery cable clamp to the negative battery post.

2. Tighten the negative battery cable nut.

3. Turn the ignition on.

  • Pages

    open all | close all